this is information on a product in full production. november 2014 docid027044 rev 1 1/10 ESDA7P60-1U1M high power transient voltage suppressor datasheet - production data features ? low clamping voltage ? typical peak pulse power: ? 700 w (8/20s) ? stand off voltage 5 v ? unidirectional diode ? low leakage current: ? 0.2 a at 25 c ? rohs compliant complies with the following standards: ? iec 61000-4-2 level 4 ? 30 kv (air discharge) ? 30 kv (contact discharge) applications where transient overvoltage protection in esd sensitive equipment is required, such as: ? portable multimedia, tablets, mobile phone, smart phone ? usb v bus protection ? power supply protection ? battery protection description the ESDA7P60-1U1M is a unidirectional single line tvs diode designed to protect the power line against ios and esd transients. the device is ideal for applications where high power tvs and board space saving are required. figure 1. pin configuration s d f n d j h 3 l q 3 l q 3 l q 3 l q www.st.com
characteristics ESDA7P60-1U1M 2/10 docid027044 rev 1 1 characteristics figure 2. electrical characteristics (definitions) table 1. absolute maximum ratings (t amb = 25 c) symbol parameter value unit v pp peak pulse voltage: iec 61000-4-2 contact discharge ec 61000-4-2 air discharge > 30 > 30 kv p pp peak pulse current (8/20 s) 700 w i pp peak pulse current (8/20 s) 60 a t stg storage temperature range - 55 to +150 c t op operating junction temperature range -55 to +150 c 9 9 9 , 5 0 , 5 , 3 3 9 , , ) 9 9 6 o r s h 5 g 9 9 & / 9 % 5 5 0 9 ) table 2. electrical characteristics (values, t amb = 25 c) symbol test conditions min. typ. max. unit v br i r = 1 ma 6.4 6.8 7.2 v i rm v rm = 5 v 200 na v cl i pp = 60 a 8/20 s 10.2 11.6 v r d 8/20 s 0.06 ?
docid027044 rev 1 3/10 ESDA7P60-1U1M characteristics 10 figure 3. peak pulse power dissipation versus initial junction temperature (typical values) figure 4. peak pulse power versus exponential pulse duration (maximum values) ? v 7 \ s l f d o y d o x h 3 3 3 : 7 m ? & 7 m l q l w l d o ? & 7 \ s l f d o y d o x h v 3 3 3 : w s ? v figure 5. peak pulse current versus clamping voltage (maximum values) figure 6. leakage current versus junction temperature (typical values) ? v 7 m l q l w l d o ? & , 3 3 : 9 & / 9 9 5 9 5 0 9 , 5 q $ 7 m ? & figure 7. esd response to iec 61000-4-2 (+8 kv contact discharge) figure 8. esd response to iec 61000-4-2 (-8 kv contact discharge) 9 g l y 9 9 9 q v g l y 9 ( 6 ' s h d n y r o w d j h 3 3 9 & o d p s l q j y r o w d j h # q v & / 9 & o d p s l q j y r o w d j h # q v & / 9 & o d p s l q j y r o w d j h # q v & / 9 9 g l y 9 q v g l y 9 ( 6 ' s h d n y r o w d j h 3 3 9 & o d p s l q j y r o w d j h # q v & / 9 & o d p s l q j y r o w d j h # q v & / 9 & o d p s l q j y r o w d j h # q v & / 9 9 p 9
package information ESDA7P60-1U1M 4/10 docid027044 rev 1 2 package information ? epoxy meets ul94, v0 ? dot indicates pin 1 in order to meet environmental requirements, st offers these devices in different grades of ecopack ? packages, depending on their level of environmental compliance. ecopack ? specifications, grade definitions and product status are available at: www.st.com . ecopack ? is an st trademark. figure 9. package dimension definitions table 3. 1610 package dimension values ref. dimensions millimeters inches min. typ. max. min. typ. max. a 0.51 0.55 0.60 0.020 0.021 0.023 a1 0.00 0.02 0.05 0.002 b 0.75 0.80 0.85 0.029 0.031 0.033 d 1.50 1.60 1.70 0.059 0.063 0.067 e 0.90 1.00 1.10 0.035 0.039 0.043 e1.05 0.041 l 0.30 0.35 0.40 0.011 0.013 0.016 e / h $ $ ( ' 7 r s y l h z 6 l g h y l h z % r w w r p y l h z
docid027044 rev 1 5/10 ESDA7P60-1U1M package information 10 figure 12. marking note: product marking may be rotated by multiples of 90 for assembly plant differentiation. in no case should this product marking be used to orient the component for its placement on a pcb. only pin 1 mark is to be used for this purpose. figure 13. tape and reel specifications figure 10. footprint, dimensions in mm figure 11. alternative footprint, dimensions in mm p p p p p p p p p p p p p p p p p p p p 3 l q 3 l q ) % d u l q g l f d w h v 3 l q 8 v h u g l u h f w l r q r i x q u h h o l q j $ o o g l p h q v l r q v d u h w \ s l f d o y d o x h v l q p p ? ? ? ? ? ? ? ? ? ) ? ? ) ) ) ) ) )
recommendation on pcb assembly ESDA7P60-1U1M 6/10 docid027044 rev 1 3 recommendation on pcb assembly 3.1 stencil opening design 1. general recommendation on stencil opening design a) stencil opening dimensions: l (length), w (width), t (thickness). figure 14. stencil opening dimensions b) general design rule stencil thickness (t) = 75 ~ 125 m 2. reference design a) stencil opening thickness: 100 m b) stencil opening for leads: opening to footprint ratio is 90%. figure 15. recommended stencil window position figure 16. alternative stencil window position / 7 : aspect ratio w t ----- 1.5 = aspect area lw 2t l w + () --------------------------- - 0.66 = p p p p p p p p p p p p p p ) r r w s u l q w 6 w h q f l o z l q g r z p p p p p p p p p p p p p p ) r r w s u l q w 6 w h q f l o z l q g r z
docid027044 rev 1 7/10 ESDA7P60-1U1M recommendation on pcb assembly 10 3.2 solder paste 1. use halide-free flux, qualification rol0 according to ansi/j-std-004. 2. ?no clean? solder paste recommended. 3. offers a high tack force to resist component displacement during pcb movement. 4. use solder paste with fine particles: powder particle size 20-45 m. 3.3 placement 1. manual positioning is not recommended. 2. it is recommended to use the lead rec ognition capabilities of th e placement system, not the outline centering. 3. standard tolerance of 0.05 mm is recommended. 4. 3.5 n placement force is recommended. too much placement force can lead to squeezed out solder paste and cause solder joints to short. too low placement force can lead to insufficient contact between package and solder paste that could cause open solder joints or badly centered packages. 5. to improve the package placement accuracy, a bottom side optical control should be performed with a high resolution tool. 6. for assembly, a perfect supporting of the pcb (all the more on flexible pcb) is recommended during solder paste printing, pick and place and reflow soldering by using optimized tools. 3.4 pcb design preference 1. to control the solder paste amount, the closed via is recommended instead of open vias. 2. the position of tracks a nd open vias in the solder area should be well balanced. the symmetrical layout is recommended, in case any tilt phenomena caused by asymmetrical solder paste amount due to the solder flow away.
recommendation on pcb assembly ESDA7P60-1U1M 8/10 docid027044 rev 1 3.5 reflow profile figure 17. st ecopack ? recommended soldering reflow profile for pcb mounting note: minimize air convection currents in the reflow oven to avoid component movement. ? & v ? & ? & v 7 h p s h u d w x u h ? & ? & v ? & v 7 l p h v ? & v v h f p d [
docid027044 rev 1 9/10 ESDA7P60-1U1M ordering information 10 4 ordering information figure 18. ordering information scheme 5 revision history table 4. ordering information order code marking weight base qty delivery mode esda7p60 f (1) 1. the marking can be rotated by multiples of 90 to differentiate assembly location 2.4 mg 8000 tape and reel ( 6 ' $ 3 8 0 ( 6 ' $ u u d \ % u h d n g r z q y r o w d j h 9 w \ s , 3 3 ? v ' l u h f w l r q 8 8 q l g l u h f w l r q d o 3 d f n d j h 0 4 ) 1 3 $ table 5. document revision history date revision changes 14-nov-2014 1 initial release.
ESDA7P60-1U1M 10/10 docid027044 rev 1 important notice ? please read carefully stmicroelectronics nv and its subsidiaries (?st?) reserve the right to make changes, corrections, enhancements, modifications, and improvements to st products and/or to this document at any time without notice. purchasers should obtain the latest relevant in formation on st products before placing orders. st products are sold pursuant to st?s terms and conditions of sale in place at the time of o rder acknowledgement. purchasers are solely responsible for the choice, selection, and use of st products and st assumes no liability for application assistance or the design of purchasers? products. no license, express or implied, to any intellectual property right is granted by st herein. resale of st products with provisions different from the information set forth herein shall void any warranty granted by st for such product. st and the st logo are trademarks of st. all other product or service names are the property of their respective owners. information in this document supersedes and replaces information previously supplied in any prior versions of this document. ? 2014 stmicroelectronics ? all rights reserved
|
